new product VS-HFA30TA60CHN3 www.vishay.com vishay semiconductors revision: 28-mar-12 1 document number: 94511 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 hexfred ? ultrafast soft recovery diode, 2 x 15 a features ? ultrafast and ultrasoft recovery ? very low i rrm and q rr ? aec-q101 qualified, meets jesd 201 class 1a whisker test ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 benefits ? reduced rfi and emi ? reduced power loss in diode and switching transistor ? higher frequency operation ? reduced snubbing ? reduced parts count description VS-HFA30TA60CHN3 is a state of the art center tap ultrafast recovery diode. employing the latest in epitaxial construction and advanced processing techniques it features a superb combination of characteristics which result in performanc e which is unsurpassed by any rectifier previously available. with basic ratings of 600 v and 15 a per leg continuous current, the VS-HFA30TA60CHN3 is especially well suited for use as the companion diode for igbts and mosfets. in addition to ultrafast recovery time, the hexfred ? product line features extremely low values of peak recovery current (i rrm ) and does not exhibit any tendency to snap-off during the t b portion of recovery. the hexfred features combine to offer designers a rectifier with lower noise and significantly lower switching losses in both the diode and the switching transistor. these hexfred advantages can help to significantly reduce snubbing, component count and heatsink sizes. the hexfred VS-HFA30TA60CHN3 is ideally suited for applications in power supplies and power conversion systems (such as inverters), motor drives, and many other similar applications where high speed, high efficiency is needed. product summary package to-220ab i f(av) 2 x 15 a v r 600 v v f at i f 1.7 v t rr typ. 19 ns t j max. 150 c diode variation common cathode to-220ab anode 13 2 base common cathode 2 common cathode anode absolute maximum ratings parameter symbol test conditions values units cathode to anode voltage v r 600 v maximum continuous forward current per leg i f t c = 100 c 15 a per device 30 single pulse forward current i fsm 150 maximum repetitive forward current i frm 60 maximum power dissipation p d t c = 25 c 74 w t c = 100 c 29 operating junction and storage temperature range t j , t stg - 55 to + 150 c http://www..net/ datasheet pdf - http://www..net/
new product VS-HFA30TA60CHN3 www.vishay.com vishay semiconductors revision: 28-mar-12 2 document number: 94511 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 electrical specifications per leg (t j = 25 c unless otherwise specified) parameter symbol test conditi ons min. typ. max. units cathode to anode breakdown voltage v br i r = 100 a 600 - - v maximum forward voltage v fm i f = 15 a see fig. 1 -1.31.7 i f = 30 a - 1.5 2.0 i f = 15 a, t j = 125 c - 1.2 1.6 maximum reverse leakage current i rm v r = v r rated see fig. 2 -1.010 a t j = 125 c, v r = 0.8 x v r rated - 400 1000 junction capacitance c t v r = 200 v see fig. 3 - 25 50 pf series inductance l s measured lead to lead 5 mm from package body -8-nh dynamic recovery characteristics per leg (t j = 25 c unless otherwise specified) parameter symbol test conditio ns min. typ. max. units reverse recovery time see fig. 5 and 10 t rr i f = 1.0 a, di f /dt = 200 a/s, v r = 30 v - 19 - ns t rr1 t j = 25 c i f = 15 a di f /dt = 200 a/s v r = 200 v -4260 t rr2 t j = 125 c - 70 120 peak recovery current see fig. 6 i rrm1 t j = 25 c - 4.0 6.0 a i rrm2 t j = 125 c - 6.5 10 reverse recovery charge see fig. 7 q rr1 t j = 25 c - 80 180 nc q rr2 t j = 125 c - 220 600 peak rate of fall of recovery current during t b see fig. 8 di (rec)m /dt1 t j = 25 c - 250 - a/s di (rec)m /dt2 t j = 125 c - 160 - thermal - mechanical specifications per leg parameter symbol test conditions min. typ. max. units lead temperature t lead 0.063" from case (1.6 mm) for 10 s - - 300 c junction to case, single leg conducting r thjc 1.7 k/w junction to case, both legs conducting - - 0.85 thermal resistance, junction to ambient r thja typical socket mount - - 40 thermal resistance, case to heatsink r thcs mounting surface, flat, sm ooth and greased - 0.25 - weight -6.0- g -0.21- oz. mounting torque 6.0 (5.0) - 12 (10) kgf cm (lbf in) marking device case st yle to-220ab hfa30ta60ch http://www..net/ datasheet pdf - http://www..net/
new product VS-HFA30TA60CHN3 www.vishay.com vishay semiconductors revision: 28-mar-12 3 document number: 94511 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 1 - maximum forward voltage drop vs. instantaneous forward current (per leg) fig. 2 - typical reverse current vs. reverse voltage (per leg) fig. 3 - typical junc tion capacitance vs. reverse voltage (per leg) fig. 4 - maximum thermal impedance z thjc characteristics (per leg) i f - instantaneous forward current (a) v fm - forward voltage drop (v) 1.0 1.4 1.8 1.2 1.6 2.0 2.2 2.4 1 100 10 94070_01 t j = 150 c t j = 125 c t j = 25 c i r - reverse current (a) v r - reverse voltage (v) 0 100 200 300 400 500 600 0.01 0.1 1 10 100 1000 10 000 94070_02 t j = 125 c t j = 150 c t j = 25 c c t - junction capacitance (pf) v r - reverse voltage (v) 0 100 200 400 500 300 600 10 100 94070_03 t j = 25 c 0.01 0.1 1 10 0.00001 0.0001 0.001 0.01 0.1 1 t 1 - rectangular pulse duration (s) z thjc - thermal response 94070_04 p dm t 2 t 1 notes: 1. duty factor d = t 1 /t 2 2. peak t j = p dm x z thjc + t c single pulse (thermal response) d = 0.50 d = 0.20 d = 0.10 d = 0.05 d = 0.02 d = 0.01 http://www..net/ datasheet pdf - http://www..net/
new product VS-HFA30TA60CHN3 www.vishay.com vishay semiconductors revision: 28-mar-12 4 document number: 94511 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 5 - typical reverse recovery time vs. di f /dt (per leg) fig. 6 - typical recovery current vs. di f /dt (per leg) fig. 7 - typical stored charge vs. di f /dt (per leg) fig. 8 - typical di (rec)m /dt vs. di f /dt (per leg) fig. 9 - reverse recovery parameter test circuit t rr (ns) di f /dt (a/s) 100 1000 0 100 80 20 40 60 94070_05 i f = 30 a i f = 15 a i f = 5.0 a v r = 200 v t j = 125 c t j = 25 c i rr (a) di f /dt (a/s) 100 1000 0 25 20 5 10 15 94070_06 i f = 30 a i f = 15 a i f = 5 a v r = 200 v t j = 125 c t j = 25 c q rr (nc) di f /dt (a/s) 100 1000 0 800 200 400 600 94070_07 i f = 30 a i f = 15 a i f = 5 a v r = 200 v t j = 125 c t j = 25 c di (rec)m /dt (a/s) di f /dt (a/s) 100 1000 100 10 000 1000 94070_08 i f = 30 a i f = 15 a i f = 5 a v r = 200 v t j = 125 c t j = 25 c irfp250 d.u.t. l = 70 h v r = 200 v 0.01 g d s di f /dt adju s t http://www..net/ datasheet pdf - http://www..net/
new product VS-HFA30TA60CHN3 www.vishay.com vishay semiconductors revision: 28-mar-12 5 document number: 94511 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 10 - reverse recovery waveform and definitions ordering information table ordering information (example) preferred p/n quantity per t/r minimum order quantity packaging description VS-HFA30TA60CHN3 25 500 anti static plastic tube links to related documents dimensions www.vishay.com/doc?95222 part marking information to-220ab-n3 www.vishay.com/doc?95028 q rr 0.5 i rrm di (rec)m /dt 0.75 i rrm i rrm t rr t b t a i f di f /dt 0 (1) (2) (3) (4) (5) (1) di f /dt - rate of change of current through zero cro ss ing (2) i rrm - peak rever s e recovery current (3) t rr - rever s e recovery time mea s ured from zero cro ss ing point of negative going i f to point where a line pa ss ing through 0.75 i rrm and 0.50 i rrm extrapolated to zero current. (4) q rr - area under curve defined by t rr and i rrm t rr x i rrm 2 q rr = (5) di (rec)m /dt - peak rate of change of current during t b portion of t rr 2 - hexfred ? family 4 - current rating (30 = 30 a) 4 5 - package: 4 ta = to-220ab 3 - electron irradiated 6 7 - voltage rating (60 = 600 v) 1 - vishay semiconductors product - circuit configuration: c = common cathode 8 - h = aec-q101 qualified 9 device code 5 1 3 2 4 6 7 8 9 vs- hf a 30 ta 60 c h n3 - environmental digit: n3 = halogen-free, rohs compliant and totally lead (pb)-free http://www..net/ datasheet pdf - http://www..net/
legal disclaimer notice www.vishay.com vishay revision: 12-mar-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products no t expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale , including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding th e design or manufacture of the part. please contact authorized vishay personnel t o obtain written terms and conditions regardin g products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. http://www..net/ datasheet pdf - http://www..net/
|
